[100% New Questions] Update Latest 300-115 Dumps Cisco PDF Materials And VCE Youtube Free Try
leads4pass offers latest Cisco CCDP 300-115 dumps pdf training materials and study guides free download. Prepare for Cisco 300-115 exam with best Cisco CCDP 300-115 dumps pdf resources and dumps vce youtube update free demo. https://www.leads4pass.com/300-115.html dumps exam practice files. High quality Cisco CCDP 300-115 dumps exam questions and answers free try, pass Cisco 300-115 exam test easily at the fiest time.
Latest Cisco 300-115 dumps pdf training materials free download: https://drive.google.com/open?id=0B_7qiYkH83VROUdnZWRYLTJta1E
Latest Cisco 300-101 dumps pdf training materials free download: https://drive.google.com/open?id=0B_7qiYkH83VRWFlVNGtTZjU1MVE
Vendor: Cisco
Certifications: CCDP
Exam Name: Implementing Cisco IP Switched Networks
Exam Code: 300-115
Total Questions: 437 Q&As
QUESTION 1
After the recent upgrade of the switching infrastructure, the network engineer notices that the port roles that were once “blocking” are now defined as “alternate” and “backup.” What is the reason for this change?
A. The new switches are using RSTP instead of legacy IEEE 802.1D STP.
B. IEEE 802.1D STP and PortFast have been configured by default on all newly implemented Cisco Catalyst switches.
C. The administrator has defined the switch as the root in the STP domain.
D. The port roles have been adjusted based on the interface bandwidth and timers of the new Cisco Catalyst switches.
Correct Answer: A
QUESTION 2
While working in the core network building, a technician accidently bumps the fiber connection between two core switches and damages one of the pairs of fiber.
As designed, the link was placed into a non-forwarding state due to a fault with UDLD. After the damaged cable was replaced, the link did not recover. What solution allows the network switch to automatically recover from such an issue?
A. macros
B. errdisable autorecovery
C. IP Event Dampening
D. command aliases
E. Bidirectional Forwarding Detection
Correct Answer: B
QUESTION 3
What effect does the mac address-table aging-time 180 command have on the MAC address- table? 300-115 dumps
A. This is how long a dynamic MAC address will remain in the CAM table.
B. The MAC address-table will be flushed every 3 minutes.
C. The default timeout period will be 360 seconds.
D. ARP requests will be processed less frequently by the switch.
E. The MAC address-table will hold addresses 180 seconds longer than the default of 10 minutes.
Correct Answer: A
QUESTION 4
After UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD packets. This port continues to reestablish until after eight failed retries. The port then transitions into the errdisable state. Which option describes what causes the port to go into the errdisable state?
A. Normal UDLD operations that prevent traffic loops.
B. UDLD port is configured in aggressive mode.
C. UDLD is enabled globally.
D. UDLD timers are inconsistent.
Correct Answer: B
QUESTION 5
What is the function of NSF?
A. forward traffic simultaneously using both supervisors
B. forward traffic based on Cisco Express Forwarding
C. provide automatic failover to back up supervisor in VSS mode
D. provide nonstop forwarding in the event of failure of one of the member supervisors
Correct Answer: D
QUESTION 6
After reviewing UDLD status on switch ports, an engineer notices that the.” Which statement describes what this indicates about the status of the port?
A. The port is fully operational and no known issues are detected.
B. The bidirectional status of “unknown” indicates that the port will go into the disabled state because it stopped receiving UDLD packets from its neighbor.
C. UDLD moved into aggressive mode after inconsistent acknowledgements were detected.
D. The UDLD port is placed in the “unknown” state for 5 seconds until the next UDLD packet is received on the interface.
Correct Answer: A
QUESTION 7
Refer to the exhibit.
What is the result of the configuration? 300-115 dumps
A. The EtherChannels would not form because the load-balancing method must match on the devices.
B. The EtherChannels would form and function properly even though the load-balancing and EtherChannel modes do not match.
C. The EtherChannels would form, but network loops would occur because the load-balancing methods do not match.
D. The EtherChannels would form and both devices would use the dst-ip load-balancing method because Switch1 is configured with EtherChannel mode active.
Correct Answer: B
QUESTION 8
A network engineer tries to configure storm control on an EtherChannel bundle. What is the result of the configuration?
A. The storm control settings will appear on the EtherChannel, but not on the associated physical ports.
B. The configuration will be rejected because storm control is not supported for EtherChannel.
C. The storm control configuration will be accepted, but will only be present on the physical interfaces.
D. The settings will be applied to the EtherChannel bundle and all associated physical interfaces.
Correct Answer: D
QUESTION 9
Which technique automatically limits VLAN traffic to only the switches that require it?
A. access lists
B. DTP in nonegotiate
C. VTP pruning
D. PBR
Correct Answer: C
QUESTION 10
An access switch has been configured with an EtherChannel port. After configuring SPAN to monitor this port, the network administrator notices that not all traffic is being replicated to the management server. What is a cause for this issue?
A. VLAN filters are required to ensure traffic mirrors effectively.
B. SPAN encapsulation replication must be enabled to capture EtherChannel destination traffic.
C. The port channel can be used as a SPAN source, but not a destination.
D. RSPAN must be used to capture EtherChannel bidirectional traffic.
Correct Answer: C
QUESTION 11
A network engineer deployed a switch that operates the LAN base feature set and decides to use the SDM VLAN template. 300-115 dumps The SDM template is causing the CPU of the switch to spike during peak working hours. What is the root cause of this issue?
A. The VLAN receives additional frames from neighboring switches.
B. The SDM VLAN template causes the MAC address-table to overflow.
C. The VLAN template disables routing in hardware.
D. The switch needs to be rebooted before the SDM template takes effect.
Correct Answer: C
QUESTION 12
An administrator recently configured all ports for rapid transition using PortFast. After testing, it has been determined that several ports are not transitioning as they should. What is the reason for this?
A. RSTP has been enabled per interface and not globally.
B. The STP root bridge selection is forcing key ports to remain in non-rapid transitioning mode.
C. STP is unable to achieve rapid transition for trunk links.
D. The switch does not have the processing power to ensure rapid transition for all ports.
Correct Answer: C
Reference: https://www.leads4pass.com/300-115.html dumps exam practice questions and answers update free try.
Watch the video to learn more: https://youtu.be/wyXFLuYtFpI